Rick's Free Auto Repair Advice

Where to get your brakes replaced?

Learn the best places to get your brakes replaced

The best place for a brake job is a locally owned independent shop with good online reviews. The worst place to get brakes replaced is at any of the large national or regional chains or franchised shops. If the shop advertises on TV or is constantly offering discount coupons for brake replacement chances are high you’re gonna get ripped off on a brake job.

Why chain and franchise shops are the worst places to get your brakes replaced

You’ll never pay the “special” or “sale” price

Some shops advertise a $299 or $379 brake job “special.” For that money, you supposedly get “premium” brake pads with a “lifetime guarantee.”However, a brake job is more than just a new set of pads. In fact, slapping new pads on old brake rotors is the best way to wind up with brake noise. So a real brake job requires machining the old rotors or new rotors.

As you can see below, real high-quality OE quality brake pads retail for around $140 and it takes about an hour to do a brake job, plus another 45 minutes to machine rotors.

So a shop that’s advertising a $299 brake job would be losing money because the “special” price doesn’t even cover the full cost of the labor.

So how can they sell a brake job for $299? They can’t. It’s just that simple. If you think you’re going to get out of the shop for $299 or $379, you’re kidding yourself. They will ALWAYS find expensive parts like rotors, calipers, and hardware that “must be replaced.” By the time they’re done, your bill will be closer to $1,100.

Here’s how much a brake replacement costs

Let’s take a 2015 Chevrolet Equinox and look at the typical costs for a brake job.

• The flat-rate labor guide shows the time to remove and replace brake pads (front or rear) is 1.0-hr. This includes cleaning and lube/replace brake hardware and adjusting brake where necessary.
• The labor to replace rotors with new parts is 0.75-hr.,
• The shop price on new OE quality brake pads is around $140
• The shop price on 2 new brake rotors @ $145 ea ($290)

So total labor for replacing pads and machining rotors or replacing rotors is 1.75 hrs. At $140/hr. that’s $245.

Total brake replacement cost if the shop replaces the rotors

At $140/hr. shop rate: $245 labor plus $430 pads and rotors = $675 plus shop supplies

Here’s how chain and franchise shops rip you off on brake replacement

They use low-quality parts

Chains buy cheap brake pads in bulk from an off-brand/offshore supplier. Their cost? Usually no more than $10-$15 per set. They call them “premium brake pads,” but there’s no industry standard for premium brake pads. You think they’re good because they offer a lifetime warranty. Think about that; they’re offering a lifetime warranty on a part that’s specifically designed to wear out! How can they do that? Because they know you’ll be back and they’ll find other ways to charge you.

In less than a year—two max, you’ll be back to get the noisy, worn-out pads replaced under warranty. No problem, they’ll replace the pads for free. But the warranty doesn’t include labor. So you’ll pay the labor charge to replace the pads and they’ll pressure you into replacing the rotors and calipers at the same time, which aren’t covered by the lifetime warranty.

Let’s assume you stick to your guns again and refuse the extras. You’ll pay for 1-hr shop labor to replace the pads, around $140. Now you’re at $815 ($675 + $140) for your $299 brake job. Guess where you’ll be a year from now? Yep, back in the same place getting another replacement set of pads and another labor charge. See where this is going?

What’s the difference between an economy brake pad, OE pad and a premium brake pad? Don’t get screwed by this brake job ripoff. Read this post.

The brake pad backing plate is just as important as the friction material. Read this post to learn about early brake failure caused by cheap backing plates.

Or, you’ll be pressured into a $1,100 brake job instead of $299

Most customers don’t know enough about brakes or have enough willpower to resist the shop’s high-pressure sales tactics. Here’s the bottom line, generally speaking, nobody walks away from a $299 brake job coupon special without being hit up for new rotors, shims, a hardware kit, and new brake calipers.

• Calipers— the shop will tell you your calipers are seized and the pads are wearing unevenly. Possible? Yes. Does that mean you need new calipers? Usually not. New caliper slide pins and boots and a dab of high-temperature brake grease can return calipers to full operating condition.

• Hardware kit—these are the anti-rattle clips that keep brake noise down.

brake hardware showing Anti-rattle clips

Anti-rattle clips

But “premium” brake pads come with new clips. If they’re charging you for clips, you’re not getting premium pads

• Shims— these are thin metal/rubber plates that insulate the brake pad backing plate from the caliper to reduce noise. All premium brake pads come with new noise-reduction shims. Again, if the shop is selling you premium pads but charging you extra for shims, well, they’re not providing premium pads.

What are shims? What do they do, and are there different quality shim? Read this post

new brake pad shims

• Rotors— If your old brake rotors are worn down past their “discard thickness” they must be replaced. There’s no way around that. Also, if they have deep grooves, they should also be replaced. Finally, it’s always best practice to install new rotors with new pads or at least refinish the old rotors. That’s the best way to reduce brake noise.

Brake rotors come in economy and premium versions. What’s the difference? Read this post

 

new brake pad shims

• Rotors— If your old brake rotors are worn down past their “discard thickness” they must be replaced. There’s no way around that. Also, if they have deep grooves, they should also be replaced. Finally, it’s always best practice to install new rotors with new pads or at least refinish the old rotors. That’s the best way to reduce brake noise.

Brake rotors come in economy and premium versions. What’s the difference? Read this post

How bad are the parts from chain shops?

I already discussed how chain shops often sell economy brake pads but represent them as premium pads. They don’t last as long. They make noise. They rust.

But what about their new brake rotors? Aren’t all brake rotors the same? Nope. Large chain repair shops can buy brake rotors for around $10 each and sell them for up to $140 each. What’s the difference? Take a look.

photos of an economy brake rotor compared to an OE brake rotor

See the difference between economy brake rotors and OE quality brake rotors

Economy brake rotors don’t brake as well because they have less metal and non-OE cooling vanes. Straight cooling vanes cost far less than the OE style shown above.

How much can chain repair shops save by buying economy parts?

The shop’s wholesale cost on high-quality brake rotors for a Chevrolet Equinox is around $40 each. But a chain can buy the rotors for the Equinox from China for around $2 each. Don’t believe me? Just go to Alibaba and order online.

picture of brake rotors from alibaba

Buy brake rotors in bulk and you can pay as little as $2 each

brake pads from Alibaba

Buy brake pads in bulk and you can pay as little as $1.80 per set

Brake Job Horror Stories

Liane S tells the story of her “brake job from hell”

“I went to a large muffler chain for a brake job. They talked me into rotors, calipers, pads, brake drums, wheel cylinders, hardware, and brake shoes. The entire job cost over $800. Exactly one year later the front brakes were grinding. I took it back to them and they offered to replace the front pads for free (under warranty). But they wanted to replace the rotors, calipers, wheel cylinders, and rear drums again. This time they wanted $700. I asked them why brand new pads would wear out in less than 10,000 miles. They just shrugged their shoulders and told me not to worry since they were covered under warranty. I called Rick and he came over to the shop. He demanded to know why they thought I needed new calipers, rotors, wheel cylinders, and rear drums. He made them measure the rotors and drums–they were fine. So were the calipers. The shop replaced the “lifetime warranty” pads and I left the shop with no charge. If Rick hadn’t been there to help, I would have been screwed again.”

Tom F

“I had a problem with a sticking rear caliper on my Pontiac. I took it to a chain muffler shop that advertises cheap brake jobs. They insisted on replacing both rear calipers, the caliper mounting brackets, rotors, and pads. Their quote was $785. I called Rick and he explained that GM vehicles have a problem with the rear caliper pins. He recommended taking it to the dealer. I did. They removed the frozen caliper pins and installed new ones. They also resurfaced the rotors and installed factory OEM pads. The calipers were just fine. Total cost? $235. Thanks Rick! You saved me a fortune. Who would have thought that the dealer would be cheaper than the $79 brake job special?”

Here’s how to avoid brake job rippoffs

• Get brake work done at an independently owned repair shop or dealer that has good reviews.

• If the shop is trying to upsell you to different brake pads than the type installed on your car from the factory, ask them WHY they’re making the recommendation.

• If the quote includes a separate charge for hardware or shims, they’re not installing premium brake pads. Premium brake pad sets come with all the necessary hardware

• If the shop recommends new calipers, ask them WHY. Unless the caliper is leaking or not retracting, they do not need to be replaced.

• If the shop says your old calipers are seized, ask if they can replace just the bracket instead of the entire caliper. Rebuild brackets cost far less than a new caliper.

• Always ask about the brand of brake pad the shop intends to install. Is it a name brand or a store brand? Is it OE or premium quality? In my personal opinion, store brands are lower quality than name brands and they cost about the same price.

• A brake fluid flush isn’t always necessary. If the shop recommends it, ask them if they’ve tested the brake fluid to determine if it should be changed. Brake fluid color is NOT an indicator of condition. Shops use a refractometer or electrical tester to determine brake fluid moisture content and test strips to determine copper content and pH. If your brake fluid has been tested and failed, have the shop perform a brake fluid flush.

• Ask the shop if there’s a bedding procedure for your new brakes and ask if they’ve performed the procedure before you leave.

©. 2019 Rick Muscoplat

Posted on by Rick Muscoplat



Custom Wordpress Website created by Wizzy Wig Web Design, Minneapolis MN