Rick's Free Auto Repair Advice

Change oil

When to change oil

When to change oil in your car or truck isn’t as complicated as you think. In fact, it’s all right there in your owner’s manual maintenance guide. Those aren’t just lofty suggestions; the car makers really mean what they say. Forget about the advice you get from self proclaimed Internet “experts.” There’s no universal answer on oil change intervals.

When to change oil is dependent on the year, make, model, engine, and your particular driving habits.

If you’d like to know more about oil click on the links below.

Choosing the right motor oil

Chrysler’s 3.5-liter engine has oil sludge issues

High mileage oil and oil filters

Oil Viscosity Warning

Synthetic Oil Facts and Myths

Synthetic oil versus conventional oil

What motor oil to use

What oil brand is best

What oil should you use

Best Oil filter

Subaru trouble code due to oil sludge from going too long between oil changes

Cam phaser trouble code due to oil sludge from going too long between oil changes

Updated oil life monitoring system information from GM

When to change oil comes up more often these days because more owners are switching over to synthetic oil and most new cars require synthetic oil. Many self-proclaimed experts (numbskulls) spout off that you can easily go 7,000- 10,000 miles between changes with synthetic oil. Well, I’ve got news for you; it doesn’t matter what they think. It’s what’s in the car makers maintenance schedule that counts. Oil change intervals are based on many factors. The rate at which oil and its additives are used up depends on several factors including the year, make, and which engine you have as well as HOW you drive as well as how far you drive. So, anyone who gives you a flat mileage change interval with first asking how you drive is someone who really doesn’t understand oil.

Factors that determine when to change oil

Engine design determines when to change oil

1) Which engine do you have? What year? Every engine has different operating characteristics. Engines with turbos are MUCH harder on oil than

oil life with synthetic oil

A turbo charger runs hot and can degrade oil faster. If you have a turbo, don’t go beyond the car maker’s oil change recommendations

normally aspirated engines. Engines with variable valve timing (VVT) alter camshaft timing by pulsing oil pressure to a cam phaser. When you pulse oil, it tends to foam, so the oil’s anti-foaming additives must be up to the job. They deplete faster in an engine with VVT than in an engine with fixed valve timing. So you have to change oil more often.

The VVT mechanisms are very finely calibrated. You must use the exact oil viscosity listed in the owner’s manual. Use a different weight oil, and the pulsing system will be thrown off and you’ll set a check engine light. Worse yet, incorrect valve timing can throw off your emissions, causing the engine to dump too much unburned fuel into the catalytic converter and damaging it. To prevent oil sludge and particle clogging, most VVT mechanisms have a screen filter. If you exceed the car makers recommendations on when to change oil, your oil will develop sludge which clogs the filter, causing a check engine light. In many cases, you have to replace the VVT actuator or phaser. OUCH. The online numbskulls that told you to go longer between changes won’t pick up the repair bill for that one!!!

The type of fuel injection determines when to change oil

Many late model cars and trucks have gasoline direct injection. Gasoline direct injection works by injecting gas directly into the combustion chamber at extremely high pressures –like 2,000-psi. These vehicles use two separate fuel pumps. The fuel pump in the tank

oil life with synthetic

High pressure fuel pump and camshaft lobe wear

pumps fuel to the high pressure fuel pump driven by a triangular camshaft lobe. The engine oil must have incredible anti-shear properties and must be changed on schedule. If you exceed the car maker’s recommendations on when to change oil, you can cause major engine damage, requiring a new camshaft and high pressure fuel pump. We’re talking about damage in the thousands here.

Shops are seeing a huge increase in camshaft replacements due to owners exceeding the car maker’s oil change recommendations. Once again, who do you trust for reliable information on when to change your oil—online numbskulls or the car maker’s maintenance guide?

In addition, GDI engines create more soot. That soot goes into the crankcase where it mixes with moisture, stressing the oil’s dispersant and anti-corrosion additives to create sludge.

Then there’s the issue of timing chains. Once again, shops are seeing a huge increase in the number of stretched timing chains due to delayed oil changes. And again, this is engine specific. Saturn Outlook engines, for example are known for destroying timing chains if the oil changes aren’t done on time. Timing chain wear and stretch can happen is as little as 15,000 miles. That means you can be looking at am $800  (minimum) repair bill simply by going several thousand miles past the recommended interval. Hey numbskulls, where are you NOW????

How you drive determines when to change oil

Engines are designed to run on a very lean mixture to save gas. But engines won’t start with a lean mixture. So the computer provides a rich air/fuel mixture to start the engine. However, all engines (even brand new ones) leak a small portion of the air/fuel and exhaust through the piston ring gaps and into the crankcase. That’s called “blowby.” The raw gasoline in cold start blowby gasses enter the crankcase and dilute the engine oil, thinning it out and reducing its lubrication effectiveness. As the engine warms up and the air/fuel mixture leans out, the blowby contains less raw gas.

If you drive long enough the engine heat heats up the raw gas

when to change oil

Example of sludge buildup in neglected engine. (PHOTO reddit.com/r/Justrolledintotheshop/)

and moisture and it evaporates, gets sucked out by the PCV valve and burned in the engine. However, if you start a cold engine and drive it a short distance, the engine never gets hot enough to evaporate the gas and water and that’s what forms corrosion and sludge.

Aside from raw fuel, blowby gases also contain exhaust byproducts like soot and water. In fact, for every 100 gallons of gasoline, you produce 90-120 gallons of water, 3-10 gallons of unburned gasoline, .5 to 3-lbs. of soot and carbon, 0.25-1-lb. of varnish, and 1-4-lbs. of sulfuric and nitric acid. Most of it goes out the tailpipe, but some of it flows into the crankcase.

Motor oil contains additives to deal with soot, water, acids, and sludge. For example, all modern motor oil contains:
• Anti-corrosive additives to prevent corrosion from water
• Dispersants to keep particles in suspension so they can reach the filter and be retained by the filter media.
• Detergents to clean deposits

Frequent cold starts deplete motor oil additives faster.

Now let’s be clear on our definitions. A “cold” engine is any engine that hasn’t been run for more than 3 hours. It doesn’t mean -30F. So, if you go to work and park your car all day and it’s 97° in the shade, it’s COLD when you start it to go home. That’s because engine operating temperature is usually 195° to 205°. So if you live in Arizona, don’t kid yourself into thinking your engine is only cold on morning startups.

Cold starts also eat up anti-wear additives

Most engine wear occurs at startup before oil pressure

when to change oil

Cold starts reduce oil life

has a chance to build and form a buffer layer between metal parts. Oil film and pressure keeps metal components apart. So the engine is slightly oil-starved on cold startups and that’s where the oil’s anti-wear additives come into play. They melt out of suspension and deposit on hot areas created by friction. So frequent cold starts deplete anti-wear additives faster.

City driving depletes viscosity index improvers (VII) and anti-oxidants

Multi-viscosity oil contains a thickening agent call

when to change oil

Stop and go city driving reduces oil life

viscosity index improver (VII). VII is a polymeric molecule that expands as it heats to “thicken” the oil and increase its viscosity. But this polymeric molecule isn’t oil, so it doesn’t lubricate. It’s a filler to thicken. When the engine is under hard acceleration, hauling heavy loads, or when you put the pedal to the metal, you create tremendous pressure on the oil film like the crankshaft and bearings or the camshaft and lifter. That pressure can shear the polymeric molecule, literally cutting it in half. As you damage the VII, you literally reduce the oil’s ability to thicken when hot. That’s why many car makers classify stop and go city driving as severe service. In addition, hot summer city driving reduces the engine’s ability to cool the oil. That results in thermal oil breakdown, causing excessive oxidation which degrades the oil. In other words, city driving depletes VII and anti-oxidant additives faster.

Short trips deplete up anti-corrosive additives

The extra fuel that’s dumped into the crankcase at cold start really needs to get burned off. Driving for longer than 20 minutes can do that. But if you just start the engine cold and run to the grocery store, the oil never gets hot enough to evaporate out the gas and water. So it sits in the oil and puts the anti-corrosive additives under stress. And that extra gas and water is what causes sludge to build up.

So what does all this mean?
By its very nature, synthetic oil has little (or no) wax (depending on whether it’s made from true Group III or Group IV base oil), so it has less pour point depressant additive. And the molecules in synthetic oil are far more uniform, so you get less thermal breakdown where the smaller molecules burn away under high heat and stress. AND, to run longer between oil change intervals it also contains a higher percentage of anti-corrosive, anti-wear, and dispersant additives. But, at best, the additives only account for 25-30% of the oil’s volume. So the question remains, can you extend the oil change intervals for your vehicle beyond the manufacturer’s recommendations? That’s a qualified maybe.

What is severe service?

Your owner’s manual will list separate oil change interval

oil change interval

Towing a trailer reduces oil life.

recommendations for Normal and Severe. Normal service is considered as “ideal” conditions. While you may consider your driving habits normal, it pays to read the fine print. These driving conditions are EXCEPTIONS to  Normal driving include:

Frequent short trips (less than 10 miles, especially during cold weather)
Stop-and-go city traffic driving
Driving in dusty conditions, on gravel roads, etc.
Driving at sustained highway speeds during hot weather
Towing use
Diesel or turbocharged engine

Oil life monitoring system determines when to change oil

To get a better feel for oil life and to reduce owner operating costs, many manufacturers now include an oil life monitoring system. The original “oil change” indicators were simply based on mileage. But the newer systems actually track the number of cold starts, engine load, time driven, ambient temps and engine temperatures. Based on the manufacturer’s algorithm and your driving habits, the oil change light may come on at 4,000 miles of stop and go city driving, or 7 to 10,000 miles of highway driving.

Oil level determines when to change oil

Oil life monitoring systems aren’t smart enough to track two important items. First, unless you own a luxury car with an oil level sensor, the oil life monitoring systems don’t track oil level. Secondly, they don’t know what oil you installed. With engines running longer between oil changes, the driving public has become complacent about checking oil levels. That’s a HUGE mistake. In fact, shops are reporting an increase in engine failures due to sludge and wear due to running the engine while it’s low on oil.

Some engine sumps hold only 4-qrts. During a 7,000 mile oil change interval, you’re likely to burn ½ to 1-qrt of oil. If you don’t routinely check your

oil dip stick, check oil level

Find the dip stick on your engine and pull it straight out.

oil level, you’re probably running the engine with less than a full fill. Running low on oil puts added stress on the remaining oil. So the remaining anti-oxidant, acid neutralizers, detergents, and dispersants are used up MUCH faster due to the added stress. Unfortunately, the oil life monitoring system doesn’t KNOW you’re low on oil. It assumes that you’re a conscientious owner and check your oil levels regularly. Most owners think the oil light will come on when their low on oil. Not true. Some luxury cars have an oil level sensor, but most vehicles just have an oil PRESSURE sensor. So the oil light only comes on when you’ve lost oil pressure. By that point you’ve been running low on oil for a long time (unless the loss of pressure is due to a leak). So don’t even think of extending your oil changes if you never check your oil levels.

Next, the oil life monitoring system assumes you’ve used the correct oil. GM, for example, requires DEXOS oil in late model vehicles. The oil life monitor depends on you follow the car makers recommendations so it know exactly how much of each additive is in the oil. If you install a non-recommended oil, all bets are off as far as following the oil life monitor.

Is the oil life monitor accurate?
Well, it’s an algorithm and it’s only as good as the engineer that wrote it. At least one major car maker has been forced to go back and reprogram their customer’s cars to reduce the oil change intervals because the algorithm has proved itself wrong in real world use.

How about oil brands that claim you can get 25,000 miles between changes?
I’m not going to knock any company’s synthetic oil. Oil makers like Amsoil and Royal Purple make excellent products. They claim you can go 15K or 25K miles between oil changes, and they back it up with a guarantee. Or do they?

Before you jump on the 25,000 mile bandwagon, read the fine print in the oil manufacturer’s warranty. You’ll see that many of them reduce their recommended oil change intervals down to 15,000 miles if you do short trips. What’s their definition of a short trip? Anything less than 10-miles, according to one oil manufacturer.

Another large manufacturer tells you to follow the car maker’s oil change intervals while you’re under either the manufacturer’s warranty or an extended warranty, then switch to an their extended interval once you’re out of warranty. You should wonder why, if they’re so confident that their oil will go the distance aren’t they willing to back up their extended drain intervals WHILE you’re under the car maker’s warranty?

The same issue applies to oil maker’s engine warranties. If you read the fine print on the engine guarantee, you’ll discover the terms you must follow to get coverage for the full 300,000 miles. The warranties require you to use ONLY their oil and follow the CAR MAKERS’ recommendations for oil change intervals. Get it? They’re not willing to put their money on the line with extended oil change intervals either.

The only way you can safely extend oil change intervals is with oil analysis

The ONLY way to answer the “how long can I go between changes?” question with confidence it to perform oil analysis, where you send in a sample and actually see how many of the additives remain. But even that approach can be misleading. Because you CANNOT depend on a single sample. Think about this; you take a sample and the lab results show very little additive degradation and low amounts of wear metals at 4,000 miles. Does that automatically mean you can extrapolate the results to conclude you can go 10,000 miles? Absolutely not! You must conduct a second oil analysis at 7,000 miles to track the RATE of additive degradation and wear metal content. IF the oil still checks out, then conduct a 3rd sample near 10,000 miles. If that sample shows good additives concentrations and low wear metals, THEN you can conclude that that particular brand of motor oil can go the distance in YOUR PARTICULAR car with YOUR particular engine. You CANNOT extrapolate the results to conclude that that oil will perform the same in ALL engines and for anybody’s driving style.

Oil analysis costs about $25 a pop. So it’ll cost you $75 to find out how long one particular brand of oil will last in your vehicle. Don’t want to go through the time and trouble? Fine. Then follow the car makers’ schedule. Do NOT go by your buddy’s recommendations or advice you hear on the Internet. NOBODY can tell you how long your can go between oil changes, because NOBODY knows your driving habits. Get it?
In conclusion:
Shops are seeing a huge increase in engine damage due to customer’s extending their oil change intervals beyond car makers’ recommendations. If you drive under severe conditions (as defined by the car maker, not your buddy), but use longer oil change intervals based on normal driving, you WILL cause premature wear on the timing chain, camshaft, crankshaft, bearings, lifters, etc. The cost to repair those items range from $1,000 to as much as $5,000.

If you follow Internet advice to extend oil change intervals beyond the manufacturers’ recommendations and damage your engine, you have no recourse against those who gave you the bad advice.

Bottom line:
Oil changes are cheaper than new engines. Change it according to the manufacturers’ recommendations, not some Internet idiot’s advice
All motor oil contains additives. They are:
Anti-corrosives to prevent corrosion
Anti-oxidants to slow the breakdown of oil
Detergents to clean deposits
Dispersants to keep particles from settling out so they can reach the filter
and be captured.
Anti-wear agents that melt onto metal surfaces that have been heated by
Anti-foaming agents.
Viscosity Index Improvers to thicken oil as it heats up
Pour point depressants to make oil flow better on cold start-ups
Friction modifiers to reduce friction and improve gas mileage
Seal conditioners to prevent seals from hardening, cracking, and leaking.

© 2012 Rick Muscoplat





Posted on by Rick Muscoplat

Custom Wordpress Website created by Wizzy Wig Web Design, Minneapolis MN